PGT Sliding Glass & Patio Doors Nationwide | TruePane Windows & Doors

PGT Sliding Glass & Patio Doors in Plantation: What to Know First

We service and repair PGT sliding glass and patio doors throughout Plantation, FL as an independent PGT service provider. Most PGT slider issues, including roller replacement, track repair, and lock realignment, are completed in one visit, with labor typically running $165 to $385 depending on what has worn out. Replacement doors and full frame work run higher, and we quote those on paper after measuring the opening. If you own a PGT slider in Plantation and it binds, drags, leaks, or will not lock, call (772) 577-2915 and we will tell you straight what you are looking at.

Call (772) 577-2915

How PGT Products Fail - and How We Fix Them

• PGT 5500 Series sliders: worn bottom rollers after years of Florida grit. Plantation sits on sandy soil, and that fine grit gets tracked onto the track every time a slider opens. The original rollers on 5500 Series doors use nylon wheels that grind down against sand over five to eight years. The door still closes, but you feel it dragging, then it starts jumping the track. We pull the panel, replace the rollers with updated OEM or better aftermarket units, and clean the track channel so the new wheels ride clean.
• PGT 7700 and WinGuard sliders: lock stile misalignment from humidity cycling. Impact-rated PGT doors are heavy, and their frames move with South Florida moisture swings. A door that latched smoothly in February can miss the keeper by a quarter inch in August. Homeowners sometimes force it, which rounds off the lock pawl. We reset the panel height with new roller adjustments, shim the stile square, and replace the lock assembly if the pawl has been chewed.
• PGT French sliders with center meeting rails: failing weatherstrip at the interlock. The interlock where the two panels meet is the first place water finds its way in on a PGT French slider. The original weatherstrip compresses over time and no longer seals. We see this most often on Plantation homes built in the 1990s and early 2000s. We replace the interlock weatherstrip with the correct profile rather than gluing in a generic strip that makes the door hard to slide.
• PGT 9500 Series: track wear on high-use patio doors. These are big, heavy panels, and when rollers are not adjusted evenly, one side of the track takes all the load. The aluminum wears into a groove, and the door rides rough forever after, no matter how many new rollers you put in. We check track condition first on any 9500 call. If the track is grooved, we either cap it or quote a replacement bottom track before touching the rollers, because rollers alone will not fix a worn channel.
• WinGuard tinted sliders: dried-out weep hole gaskets causing sill puddling. PGT’s impact sliders have weep holes along the sill to drain water from the track channel. The little gaskets in those holes dry out and shrink after a decade of Plantation sun, and the holes clog with debris. Water backs up and puddles at the interior sill. We clear and re-gasket the weep system, which takes about thirty minutes and costs far less than most homeowners expect before they call us.

Our PGT Sliding Glass & Patio Doors Process

1. 1
   Call and explain what the door is doing. A live person answers. We ask about the symptoms, the PGT series if you know it, and when the trouble started. Then we schedule the visit with a real arrival window.
2. 2
   We inspect the door in place. Our tech checks the rollers, track, lock stile, weatherstrip, weep system, and frame alignment. We measure the panel with the door closed and again with it open. The two numbers never lie.
3. 3
   Parts decision: OEM first, quality aftermarket when it is better. PGT still supplies rollers, locks, and weatherstrip for most active series. Where OEM parts are discontinued or have known shortcomings, we use aftermarket parts sourced from suppliers we have tested over years. We tell you which is which and why, in writing.
4. 4
   Repair or replacement quote on paper. If it is a repair, you get one line-item price before any work starts. If the door needs replacement, we quote PGT alongside comparable lines like CGI, CWS, ES Windows, and ECO Window Systems, side by side, so you see exactly what each dollar buys.
5. 5
   The work gets done, then tested. We set the panel, adjust the rollers so the door glides and latches square, then run it open and closed a dozen times. We check the lock, the interlock seal, and the weep drainage.
6. 6
   Both warranty layers registered in writing before we leave. If any part or door carries a manufacturer warranty, we register it and hand you the paperwork. Then we walk you through what was done and what to watch for. The Done Right Promise backs all of it.

What PGT Sliding Glass & Patio Doors Costs in Plantation

Labor ranges on repair work hold pretty steady in Plantation. Here is what we quote most often:

• Roller replacement on a standard PGT slider: $180 to $320, depending on panel weight and roller style.
• Track cleaning and realignment: $95 to $165.
• Lock and latch replacement on a 5500 or 7700 Series: $140 to $260 including parts.
• Weatherstrip and interlock seal replacement: $120 to $240, depending on door width.
• Full PGT slider replacement with impact-rated glass: $2,800 to $5,600 installed, depending on size, series, and finish options.

What moves the price is the panel size, whether the frame itself has shifted, and whether we are fixing a symptom or the cause. We quote the cause. Call (772) 577-2915 for a free estimate, and we will put the number in writing before any work begins.

Why Plantation Homeowners Call TruePane Windows & Doors for PGT Work

Dale Kessler grew up off Broward Boulevard in Plantation, learned glazing at McFatter Technical College, and spent two decades setting windows and doors across Broward County before founding TruePane in 2008. He is known for tight-tolerance installs on sliding glass doors, and that standard carries through every PGT job we take. Our techs are background-checked and uniformed, and they work in a customer’s home the way they would work in their own mother’s. Every job is covered by the Done Right Promise. Both manufacturer warranty layers get registered in writing before the truck leaves the driveway. And if the PGT door turns out to need full replacement, we quote PGT beside CGI, CWS, ES Windows, and ECO Window Systems on the same sheet of paper, so you see the spread and decide. If it is not square, level, and in writing, it is not done.

FAQs