Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterTherma-Tru Roof Repair in Plantation: What to Know First
Therma-Tru roof repair in Plantation usually means one of two things: a Therma-Tru skylight or roof-adjacent door unit that has failed at the flashing point, or a Therma-Tru door system under a roof overhang that is taking water through the header. We handle both, typically same-week, and we tell you the real number before any work starts. This page is for Plantation homeowners who own Therma-Tru products and want them repaired by someone who understands how these units actually fail in South Florida. Call (772) 577-2915 and a live person answers, day or night.
Key Takeaways
- We repair Therma-Tru roof flashings, skylight curbs, and door-to-roof junctions on homes across Plantation, from Plantation Acres to Jacaranda Lakes.
- Most Therma-Tru roof leaks are flashing failures, not door failures. We fix the root cause, not the symptom.
- We are an independent Therma-Tru service provider, not a Therma-Tru franchise, so our parts decisions favor your warranty, not a manufacturer’s markup.
- Every job carries the Done Right Promise. If the leak comes back, we make it right. No paperwork fights.
How Therma-Tru Products Fail - and How We Fix Them
Therma-Tru builds good doors. The problem in Plantation is rarely the fiberglass slab itself. It is what happens where that door meets the structure, and what the roof does to it over ten or twenty rainy seasons. Here are the five failures we see most often on Therma-Tru units in this part of Broward County.
- Flashing reglet failure on Therma-Tru Benchmark and Smooth-Star entry doors under shallow overhangs. The original aluminum flashing gets tucked into a reglet that was cut too shallow, and the first time a Plantation afternoon storm drives rain sideways, water finds the gap. We see this on 1990s-era homes in Plantation Gardens and the older sections of East Plantation. The fix is removing the old flashing, cutting the reglet deeper, bedding new flashing in a high-grade sealant, and tooling it so water has no path behind the jamb.
- Therma-Tru Slim-Line and Classic-Craft door headers wicking moisture from an improperly terminated roof above. When a flat roof or low-slope tile roof terminates above a Therma-Tru door without a proper drip edge, water runs down the stucco and pools at the header cap. The door itself is fine; the installation detail above it was wrong. We correct the termination, install or replace the drip edge, and reseal the header cap. This is the single most common call we get from Plantation Heights and Sunrise Key.
- Therma-Tru roof-mounted skylight curb assemblies leaking at the mounting flange. These are often aftermarket curb kits, not Therma-Tru-branded skylights, but they sit on Therma-Tru door openings or rooflight shafts. The flange sealant degrades under constant UV and heat, cracks, and then every afternoon shower finds it. We remove the curb, clean the substrate completely, and reset it with a UV-stable polyurethane sealant rated for South Florida exposure. A proper reset lasts years longer than the original install.
- Therma-Tru Multi-Point locking systems binding after the roof shifts above the door. Plantation sits on land that moves. Older sections near the Plantation Golf Course and the east side of town have soils that expand and contract seasonally, and a roof that settles even a quarter inch can pinch a Therma-Tru door frame. The symptom is a deadbolt that fights you, or a multi-point lock that will not throw all the way. The real cause is often structural settlement, not the lock. We correct the frame alignment, shim where it matters, and sometimes replace the lock mechanism after the frame is true. Dale Kessler has said it a hundred times: if it is not square, level, and in writing, it is not done.
- OEM Therma-Tru weatherstripping failing twice as fast on west-facing Plantation elevations. The heat load on a west-facing door in Plantation is punishing. OEM Therma-Tru weatherstripping, which is decent material, breaks down faster when it bakes for six hours every afternoon. We see this in homes along Nob Hill Road and near Central Park. We replace it with a UV-stabilized equivalent that matches the Therma-Tru profile and lasts noticeably longer in this specific climate.
Our Therma-Tru Roof Repair Process
When you call (772) 577-2915, you get a person, not a phone tree. That person schedules a tech. The tech arrives on time, in uniform, and goes through the job the same way every time.
- 1
We look at the whole assembly, not just the point of water entry. Water travels. A stain on the interior drywall near a Therma-Tru door might start eight feet away at a roof joint. Our tech checks the roof termination above, the flashing, the header, the threshold, and the door’s own seal before touching anything.
- 2
We show you what we found, in plain English, with the part in hand when possible. If a flashing is cracked, you see it. If the curb sealant has failed, you see the gap. No mystery, no upsell.
- 3
We make the parts decision with you. For anything Therma-Tru warranty-sensitive, we use OEM parts from Therma-Tru’s distribution channels. For non-warranty items like flashing and sealants, we use proven materials that match or exceed OEM spec, because OEM flashing is not always the best choice on a 30-year-old Plantation home.
- 4
The repair gets done in one visit when the job is repairable in a day. We carry the common Therma-Tru hardware, weatherstripping, and flashing materials on the truck. If a part has to be ordered, we tell you before anyone starts work.
- 5
We test before we leave. We run water over the repaired area with a hose if the job involves a leak. We cycle the lock. We check the reveal around the door. If it is not dry, it is not done.
- 6
You get the Done Right Promise in writing. If the repair fails within 90 days, we come back and fix it. No arguing. That has been the standard since Dale Kessler started this company, and it has not changed.
What Therma-Tru Roof Repair Costs in Plantation
Therma-Tru roof repair in Plantation runs from about $180 to $950 depending on what failed. Honest numbers beat vague estimates, so here is what we see most weeks.
| Repair | Typical Range in Plantation |
|---|---|
| Weatherstripping replacement, Therma-Tru door | $85 - $185 |
| Flashing reseal at header or roof termination | $180 - $340 |
| Drip edge install above Therma-Tru door | $150 - $280 |
| Skylight curb reset and reseal | $350 - $650 |
| Full flashing replacement with reglet recut | $420 - $950 |
What moves the price is access. A two-story Plantation home with a roof line that requires ladder work costs more than a one-story ranch. The age of the opening matters too; 40-year-old stucco that crumbles when you touch it means patching before we can reseal. We give you the price before any work starts, and the price does not change unless the scope changes. Call (772) 577-2915 for a free estimate that includes line items, not a hand-wave number. Seniors and veterans get a permanent 5% discount, and any repair over $250 takes $50 off.
Why Plantation Homeowners Call TruePane Windows & Doors for Therma-Tru Work
We have served Plantation and the surrounding Broward communities since 2008 through a heritage of craft that started with Dale Kessler’s father doing finish carpentry and continued through Dale’s training at McFatter Technical College in Davie. We are not a franchise with a rotating cast of subcontractors. We hire local, train apprentices into journeymen, and plan to be here in thirty years. Dale Kessler grew up off Broward Boulevard in Plantation, near the old Plantation Fashion Mall, and he still runs the company from the same principle he learned setting doors on 1960s ranch homes: a frame out of plumb at the top will make your life difficult at the bottom. When you call us about a Therma-Tru door or roof junction, the tech who arrives knows Therma-Tru lines like Classic-Craft, Smooth-Star, and Benchmark, and also knows what to do when the answer is not Therma-Tru. We service and install PGT, CGI, CWS, and ES Windows as authorized installers, so if your repair leads to a replacement decision, you get side-by-side quotes on paper, not a single-brand push. Live person answers 24/7. No voicemail tree. That is how it has been and how it will stay.
FAQs
No, not when it is done right. Therma-Tru’s door warranty covers the door slab and components, not the flashing and weatherproofing installed by a third party. Replacing or resealing flashing does not void the door warranty. We use OEM parts for door components like weatherstripping, sweeps, and lock hardware to keep the warranty intact, and we document everything in writing. Call (772) 577-2915 if you have a warranty question; we will walk you through what is covered before any work starts.
We can if the damage is to the frame, threshold, or weatherstripping. Therma-Tru fiberglass door slabs are highly resistant to water damage, so in most Plantation roof leak cases, the slab survives and the frame is what needs work. We repair or replace the frame as needed, correct the roof issue above it, and reset the door so it is square and level. If the slab itself is compromised, we will tell you and give you a replacement quote alongside the repair number. Call (772) 577-2915 to have someone look at it.
Same week in most cases, sometimes sooner. We keep Therma-Tru common parts on our trucks, and a live person answers the phone 24/7, so you will not wait on a callback to schedule. If the leak is active and water is entering the house, we prioritize it. Call (772) 577-2915 and tell us what is happening; we will give you a straight answer on timing.
Both, depending on what failed. For door hardware, weatherstripping, and any component covered by the Therma-Tru warranty, we use genuine OEM parts from Therma-Tru’s distribution network. For flashing, sealants, and curb materials, we use products matched to the South Florida climate, which sometimes outperform OEM. We will show you the parts and explain the choice before anything goes on the truck. Call (772) 577-2915 for an exact quote, and the estimate is free.
That depends on the condition of the slab, the frame, and the threshold, but years of South Florida moisture at the base often means the frame and threshold are too far gone to save. If the slab is still solid, a repair with new flashing and a corrected roof detail can add many years. If the frame is rotted or the multi-point lock is fighting itself, replacement may be the honest answer. We will show you both numbers and let you decide. Call (772) 577-2915 to schedule a free estimate, and we will walk the job with you before quoting.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Plantation and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.