Andersen Sliding & Patio Doors Nationwide | TruePane Windows & Doors

Andersen Sliding & Patio Doors: The Plantation Owner’s Guide

We stock and install Andersen-compatible sliding and patio door parts across Plantation, with most roller, lock, and weatherstrip replacements running between $185 and $520 fully installed, depending on the series and what’s actually worn out. Our trucks carry the common Andersen hardware so we can usually finish the job the same day we look at it. The way most Plantation owners discover the problem is simple: the door that used to glide with two fingers now takes a shoulder, or the lock catches wrong, or the handle dangles loose after one too many humid afternoons. If you’re reading this, you already know which door in the house we’re talking about.

Call (772) 577-2915

Which Andersen Models This Applies To

We work on the full Andersen sliding and patio door range you’ll find in Plantation homes: the 200 Series, 400 Series, Frenchwood gliding and hinged patio doors, the Perma-Shield line, and the newer Andersen A-Series. The catch with Andersen is that hardware is not universal across series. A roller that fits a 400 Series gliding door will not seat properly in a 200 Series, and Perma-Shield doors from the 1990s take a different track profile than what Andersen ships today. The surest way to identify your door is the etched glass mark in the corner, usually stating Andersen and the series, or the aluminum tag on the hinge edge. If that tag is gone, we measure the roller housing, the track width, and the panel thickness. For Andersen doors specifically, we lean on OEM parts when the door carries an active warranty, because aftermarket substitutions can void coverage. Once the warranty has run, there are quality aftermarket rollers and locks that match the OEM spec at a lower price, and we’ll show you both options on paper before any work starts.

We are an independent installer and parts provider, not an Andersen company or affiliate. We do carry and install their hardware alongside other lines including Pella, and PGT, so you get a straight comparison rather than a single-brand pitch.

Signs Your Andersen Sliding & Patio Doors Is Failing

• The door drags, grinds, or jumps off track. Most common on Plantation doors facing south or west, where years of heat and grit have worn the nylon roller flat. A flat roller drags the panel against the track and chews up the aluminum over time.
• The handle flops and the latch doesn’t catch. Andersen handles use an internal spring and a latch hook that wear independently. The handle can feel loose while the hook still works, or the hook stops engaging while the handle feels normal. Both are fixable without replacing the whole door.
• You can see daylight or feel air between the panels or at the bottom. That’s weatherstrip that has compressed past its useful life. Here in Broward County, the wet season pulses moisture through that gap, and the dry season pulls it back out, which shortens weatherstrip life compared to drier climates.
• The door self-opens or self-closes when it should stay put. This is usually a track that has settled out of level, or a worn roller on one side. Dale Kessler will tell you the frame is almost never the problem; it’s the rolling gear and track alignment giving up after 20 or 30 years.
• Condensation inside the glass unit. That’s a failed seal, not a hardware part failure, but the fix often involves swapping the sash or the insulated glass unit. We handle that too, as a glass company rather than just a parts shop.

Replacement Cost & What’s Included

In Plantation, a typical Andersen sliding door hardware replacement runs from $185 to $520 installed. At the lower end, that’s a pair of aftermarket or OEM rollers and a track cleaning with debris removal. In the middle, it’s rollers, lock, and handle set. At the upper end, you’re replacing the track cover, both panels’ rollers, weatherstrip, and adjusting the frame so the door hangs square. We give a line-item quote before the first tool comes out, and the quote tells you exactly which parts are OEM versus aftermarket. Labor is included, not buried. The Keystone Standard applies here: both manufacturer warranty layers registered in writing, durations stated, before the truck leaves the driveway. If it’s not done right, the Done Right Promise takes over, no paperwork fights, no arguing.

DIY or Call Us?

There are things you can safely do. You can vacuum the bottom track with a crevice tool, and you can clean the rollers with a rag and dry lubricant if you can reach them. What you should not do is remove a sliding glass door panel yourself. These panels run 100 to 200 pounds, tempered glass included, and a panel that tips during removal will injure you or shatter into thousands of small pieces. We’ve also seen DIY roller replacements where the adjustment screw was cranked the wrong way and the homeowner scored the track. If you’re in Plantation and the door binds, drags, or drops when you lift it, call (772) 577-2915 before it drops for the last time.

FAQs