Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterPGT Door Installation: The Plantation Owner’s Guide
PGT door installation in Plantation typically runs $850 to $2,400 installed, depending on whether you’re replacing a worn roller assembly, a sagging hinge set, or the full panel with new impact glass. We stock PGT-compatible hardware on our trucks and can usually complete the swap in one visit. Most Plantation homeowners discover the problem the same way: the door starts dragging across the track in August, or the lock bolt no longer lines up with the strike plate because the panel has settled out of square. What began as a minor annoyance becomes a door that won’t seal against afternoon thunderstorms, and in Plantation, that’s not something to put off.
Key takeaways:
- PGT doors use proprietary hinge and roller profiles; big-box generic parts often don’t seat correctly.
- We register both warranty layers in writing before we leave, per The Keystone Standard.
- Most PGT door hardware repairs in Plantation are done in a single visit.
- Every job carries the Done Right Promise. If it’s not right, we make it right.
Which PGT Models This Applies To
We install and service hardware across PGT’s residential lines most common in Plantation: the WinGuard series (impact-rated, found on the majority of Broward County homes built or retrofitted after Hurricane Andrew), the ClassicVue and EstateView lines, and the older SpectraGuard models still on plenty of 1990s ranches. Each series uses slightly different roller geometry and hinge spacing, and mixing them up is exactly how a door ends up binding within a season. PGT stamps the series name on a label near the top or bottom rail of the door panel; if the label has worn off, we measure the roller wheel diameter and the hinge pin offset to identify the line. For PGT specifically, we recommend OEM rollers and hinge sets wherever possible. The aftermarket equivalents we’ve tested don’t hold the same tolerance on the stainless steel pin, and in Plantation’s salt-laden air, a few thousandths of an inch in slop becomes a corroded, grinding mess faster than you’d expect. TruePane is an independent service provider; we are not affiliated with PGT, but we have worked on their lines for years and know which parts match which series without guesswork.
Signs Your PGT Door Installation Is Failing
- The door drags or requires a hip bump to move. Worn roller bearings have flattened or the wheel has corroded. Once the weight rides on the axle instead of the bearing, the track starts to groove, and you’re looking at track replacement too if it goes too long.
- The panel sits visibly out of level. A sagging hinge side means the hinge screws have begun pulling from the jamb or the top hinge pin has worn oval. In Plantation’s summer humidity, wood jambs soften just enough that undersized screws lose their bite.
- The lock bolt misses the strike plate by a quarter inch or more. The panel has dropped, which means the hinge side has moved. Forcing the lock closed is temporary; the real fix is re-squaring the panel, not wrenching the handle.
- You hear a grinding or metallic rasp when opening or closing. Roller housings have collected sand and salt grit from years of Florida use. The bearing is failing, and it’s wearing the track unevenly every time the door moves.
- Water pools at the door base after a hard rain. The sweep has compressed or the panel has shifted enough that the bottom rail no longer compresses the weatherstrip evenly. In Plantation’s June-to-October rain pattern, that leaks into the threshold and, over time, the subfloor.
Replacement Cost & What’s Included
For Plantation homeowners, here’s what we quote, in writing, before any work begins:
- Roller and track service (single panel): $210 to $380 installed, including OEM PGT-compatible rollers, track cleaning and alignment, and adjustment to square the panel.
- Hinge set replacement and re-hang: $340 to $620 installed, including new PGT-profile hinges, jamb reinforcement where screw holes have wallowed, and panel re-leveling.
- Full panel replacement with impact glass: $1,400 to $2,400 installed, depending on glass package and panel width. This includes removal, disposal, new weatherstripping, and warranty registration.
The range comes down to panel size, series (WinGuard hardware runs slightly higher due to the impact-rated profile), and whether the track itself needs replacing. We quote parts and labor separately on paper, and every job is covered by our Done Right Promise. If we install it and it isn’t right, we fix it. No paperwork fight, no argument. A square deal, in writing.
DIY or Call Us?
You can safely check a few things yourself: look at the track for visible grit or dents, check whether the door rubs at the top or the bottom only, and inspect the sweep for tears. You can clean the track with a dry brush and a vacuum. What you shouldn’t do is remove a PGT panel from its track to replace rollers or hinges yourself. A full impact-rated PGT panel can weigh over 250 pounds, and the hinge side is under constant tension when the panel is not perfectly supported. If it shifts while you’re working, you’re not saving money; you’re risking a crushed hand or a cracked glass package that costs more than the original repair. We get it: nobody likes paying for something they think they can handle. But if the panel is out of square, call us at (772) 577-2915. We’ll measure twice, quote it on paper, and do it the way it should have been done the first time.
FAQs
On average, PGT rollers in Plantation last 7 to 10 years before bearing wear or corrosion becomes noticeable. Homes closer to the eastern edge of Plantation, where salt air is stronger, tend to see roller failures at the earlier end of that range. We see plenty of doors from the early 2000s still on original rollers that have long since seized; the door still moves, which owners mistake for the part being fine, but the track is wearing underneath it. If your door is over 10 years old and has never had roller service, it’s on borrowed time. Call (772) 577-2915 for a free estimate on roller replacement before the track gets expensive.
Yes, in most cases the panel can be re-hung and re-squared without replacing the glass. The fix is new hinges, reinforced screw holes, and careful re-leveling. The panel is usually still sound; it’s the hardware connection to the jamb that has failed. The exception is when the door has sagged long enough that the bottom rail has rubbed against the track and compromised the frame. We’ll tell you honestly which situation you have. Call (772) 577-2915 and we’ll put eyes on it.
A roller replacement or hinge re-hang takes 60 to 90 minutes for a single panel. A full panel replacement with new impact glass is usually a half-day job, including setting the panel, adjusting for square, installing new weatherstripping, and registering the warranty. We don’t leave a second appointment hanging; the truck is stocked for the common PGT series. If you need a specific part we don’t have on board, we’ll tell you before we start, not after. Call (772) 577-2915 to schedule a time.
We stock PGT-compatible rollers, hinge sets, handles, locks, and weatherstripping for the WinGuard, ClassicVue, EstateView, and SpectraGuard lines on our trucks. The niche parts, like a custom-width impact panel or a discontinued lock body, we order from our supplier network and typically have within a few days. We also keep parts for Andersen, and Pella doors for the mixed-brand homes around Plantation. If you call with your series name or a photo of the label, we’ll usually know before we arrive whether it’s a same-visit fix. Call (772) 577-2915 and we’ll work it out on the phone.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Plantation and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.