Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterCWS Roof Repair in Plantation: What to Know First
CWS roof repair in Plantation is work we handle as an independent CWS service provider, and most single-point failures get diagnosed and fixed in one visit. We are not affiliated with or authorized by CWS, which is exactly why we can tell you the truth about parts, warranties, and whether a repair will actually hold in South Florida weather. If you own a CWS skylight, roof window, or integrated roof glazing system and it is leaking, fogging, or binding, call (772) 577-2915. We will send a technician who knows the product lines by name, not by a spec sheet they read in the truck.
This page is for Plantation homeowners who need straight answers about a CWS roof product that has started to fail. We will explain what fails, why it fails here specifically, what it costs to fix, and when replacement is the honest call.
How CWS Products Fail - and How We Fix Them
- CWS Fixed Skylight Seal Failure at the Curb Flange. On older CWS fixed skylights in Plantation, the butyl seal between the glass unit and the aluminum curb flange dries out and shrinks after ten to fifteen years of direct Broward sun. Water does not pour in; it creeps along the weephole channel and shows up as a slow stain on the drywall months later. We pull the glazing, clean the curb, reset the unit on fresh structural silicone, and retorque the retaining clips to factory spacing. The repair holds because the root cause is the seal, not the glass.
- CWS Operable Roof Window Hinge Corrosion. Plantation’s humidity plus the salt air that pushes inland from the coast eats the hinge pins on CWS manual venting roof windows faster than the manufacturer’s corrosion warranty accounts for. The symptom is a window that opens fine in December and sticks hard in August. We replace the hinge assemblies with stainless aftermarket hardware rated for coastal exposure, not the original zinc-plated parts. This is a repair CWS owners do not get from a generic roofer who has never touched the line.
- CWS Glass Unit Seal Failure in Laminated Units. CWS laminated glass roof units can develop internal fogging when the edge seal fails, usually starting at the corners. In Plantation, this shows up most often on west-facing elevations where the afternoon heat cycles the laminate edge daily. The fix is an insulated glass unit replacement, not a whole new skylight. We measure the exact unit dimensions, order from a local IG fabricator, and set the new unit into the existing frame. That saves roughly sixty percent versus a full replacement.
- CWS Flashing Boot Splits at the Upstand. On CWS curb-mounted roof windows, the rubber boot that seals the upstand to the roof deck can split along the fold lines after years of expansion and contraction. The leak presents as water running down the inside of the curb, which most people mistake for a bad window seal. We replace the boot with EPDM rated for South Florida UV, double-seal the curb corners with polyurethane sealant, and test with a water wand before we leave.
- CWS Control Rod Disconnect on Venting Units. CWS venting roof windows use a control rod linkage that can pop off the actuator pin when the window is forced against debris or a swollen gasket. The window ends up stuck open or stuck closed, and the crank spins without engaging. We reset the linkage, replace the gasket if it has compressed, and adjust the travel stops so the rod no longer overextends. It is a forty-minute fix most of the time, but the diagnosis is the part that matters.
Our CWS Roof Repair Process
Every CWS job follows the same sequence, and we do not skip steps. That is how we can put a Done Right Promise on a repair that another shop might treat as a maybe.
- 1
Call and describe the symptom. A live person answers at (772) 577-2915. Tell us what you are seeing: where the water shows up, when the window binds, whether the fog comes and goes. That detail tells us which technician to send and which parts to load on the truck.
- 2
On-site diagnostic. The technician examines the unit from the interior and the roofline. For a CWS skylight, that means checking the curb, the flashing boot, the seal channel, and the glass edge. We do not quote a repair until we have looked at all four.
- 3
Parts decision on paper. If the fix needs hardware or a glass unit, we show you the OEM option and the quality aftermarket option side by side, with prices. CWS owners in Plantation often choose aftermarket stainless hinges or EPDM boots because they are built for this climate, not a generic one.
- 4
The repair. We remove only what needs removing, set the new parts to factory tolerance, and seal every penetration with materials rated for Florida exposure. If the pane is not true, the job is not done.
- 5
Water test and walkthrough. We run a water wand on the repair, then bring you up to see what was done and why. You get the warranty paperwork before we leave, not emailed later.
What CWS Roof Repair Costs in Plantation
CWS roof repair pricing in Plantation depends on the failure, but here are honest ranges for the most common jobs. A curb-mounted skylight reseal runs $320 to $580. A hinge replacement on a venting CWS roof window costs $180 to $340. An insulated glass unit replacement for a fogged CWS fixed skylight runs $650 to $1,100 depending on size and laminate. A flashing boot replacement lands between $280 and $520. Full frame replacement starts around $1,800 and climbs with deck work and curb modification.
What moves the price most is roof access. If the unit sits on a steep second-story pitch and we need to stage scaffolding or tie off harnesses, you will see that reflected in the quote as a line item, not buried in the total. We charge for what we do, and the price you approve is the price on the bill. If the repair is not straightforward once we open the curb, we stop and call you before any additional dollar is spent.
Every estimate is free. Call (772) 577-2915 and we will give you a written number before any work begins.
Why Plantation Homeowners Call TruePane Windows & Doors for CWS Work
We have been in this trade for over four decades, and Dale Kessler founded this company because he kept seeing CWS and other brand installs that were set out of square and left to fail. A CWS roof window is only as good as the set of hands that installed and serviced it. Our technicians measure every opening twice, quote on paper, and register both warranty layers in writing before the truck leaves your driveway.
We work on more than just CWS. If your Plantation home has PGT, CGI, ES Windows, or ECO Window Systems products elsewhere, the same tech can inspect those while we are on-site. That multi-brand knowledge matters because most Broward homes have a mix of manufacturers, and the guy who only knows one line misses the joint where the lines meet. The Done Right Promise covers every repair we do, no paperwork arguments. If it is not square, level, and in writing, it is not done.
FAQs
On most CWS products, the glass warranty stays intact if the frame and flashing are not modified and the repair is done to factory specification. As an independent CWS service provider, we are careful to use sealants and parts that do not compromise the original warranty. If a repair would put the warranty at risk, we will tell you that before we touch the unit. Call (772) 577-2915 and we will walk you through what your specific unit’s warranty says.
Most single-point CWS repairs are completed in one visit, usually two to three hours. The exception is a glass unit replacement, which requires ordering the new unit to size and typically takes three to five business days from measurement to install. We schedule the return visit at the time of the initial diagnostic, so you are not left waiting on a callback.
Fogging means the edge seal on the insulated glass unit has failed. In most cases, the glass unit can be replaced without touching the frame or the curb, and that costs a fraction of a full skylight replacement. The key is measuring the unit correctly and using an IG fabricator that matches the CWS laminate and low-E stack. We do this regularly for Plantation homes.
For repairs that stay within the existing frame and flashing, the Florida Building Code generally does not require a permit. When the repair involves structural curb modification or a complete unit replacement with changed dimensions, we pull the permit and schedule the inspection. You will never find out after the fact that a permit was needed and skipped.
Tell us what the hardware looks like and where the label might be on the frame edge, or send a photo from inside. Most CWS units have the manufacturer mark etched into the glass corner or stamped on the hinge. Our technician will confirm the brand on-site before any parts are ordered. Call (772) 577-2915 and we will help you identify what you have.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Plantation and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.