PGT Custom & Geometric Windows Nationwide | TruePane Windows & Doors

PGT Custom & Geometric Windows in Plantation: What to Know First

PGT custom and geometric windows in Plantation typically take three to six weeks from template to install, and a proper diagnosis call runs about an hour. TruePane Windows & Doors charges a straightforward diagnostic fee, then gives you a written, line-item quote before any work begins. That quote stays the price unless you change the scope.

Call (772) 577-2915

If you own a PGT arched, radius, trapezoid, or oversized custom window that is fogging, leaking, binding, or simply not closing square anymore, this page is for you. We are an independent PGT service provider, not a PGT dealer or factory shop, which means we answer to you, not to a manufacturer’s sales quota. Our techs measure every opening twice, quote OEM and quality aftermarket parts side by side on paper, and register both warranty layers in writing before the truck leaves your driveway. Call (772) 577-2915 and a live person answers, day or night.

How PGT Products Fail - and How We Fix Them

PGT builds a solid impact window. But custom and geometric shapes multiply the number of stress points on any window, and Plantation’s humidity, afternoon thunderstorms, and salt-tinged air exploit weak seals faster than the brochure suggests. Here is what we see on PGT jobs in the field:

• Fogging between the panes on PGT WinGuard arched units. This is the number one call we get from Plantation. The curved laminated glass in a WinGuard radius window flexes slightly with temperature swings, and over ten or twelve years the edge seal along the curve gives out. Moisture gets in, the low-E coating starts to haze, and the window looks like a shower door. The fix is glass replacement, not a full frame swap. We template the curve precisely, order laminated impact glass cut to the exact radius, and reset the sash in the existing frame. On a PGT frame that is still square and structurally sound, that saves thousands compared to a full replacement.
• Binding sashes on PGT 400 Series custom trapezoids. A trapezoid window puts uneven weight on its hinges and lock points. If the rough opening was even a sixteenth out of plumb when the original install went in, the sash leans and starts dragging at the top corner. We see it regularly on 1980s and 1990s Plantation homes where the original builder framed fast. Our fix starts with re-shimming the frame back to square where possible, then re-setting the sash and adjusting all lock points. If the frame has sagged beyond correction, we quote a new custom trapezoid in the same PGT line or a better current equivalent.
• Failed rollers and tracks on PGT Series 5500 sliding glass doors with sidelight transoms. Sliders are the weak link in any South Florida door setup, and when a PGT slider carries a heavy transom above it, the roller bearings take extra load in direct sunlight on a west-facing Plantation wall. Homeowners report the door “suddenly got heavy” about eight years in. That is the rollers flattening. We stock common PGT roller assemblies and swap them in one visit, and we set the door height so the locking hardware lines up true again.
• Leaking at mull joints on multi-panel PGT impact windows with radius tops. PGT factory-mulls most custom geometric builds, but over time the mull sealant at the joint between an arched panel and its rectangular neighbor dries and cracks under Plantation’s UV load. Rain water from a summer storm finds the gap. We dig out the old sealant, re-mull with a commercial-grade structural silicone rated for Florida’s climate, and re-seal the exterior flange. The repair is invisible from the street, and it stops the water at the exact point where it was getting in.
• Crank-out hardware wear on PGT Eze-Breeze style casements and awnings. Geometric casement windows in Plantation kitchens and sunrooms get opened daily, and the crank operator gear strips over time. PGT hardware is generally good, but any operator has a service life measured in open-close cycles, not years. We replace worn operators with OEM or equal-quality aftermarket units, lubricate the hinge tracks, and test the full open-close travel three times before we walk away from the window.

Our PGT Custom & Geometric Windows Process

Every PGT job follows the same sequence, and we don’t skip steps. Dale Kessler grew up off Broward Boulevard and learned his craft at McFatter Technical College in Davie, then spent two decades setting windows on everything from 1960s ranch homes to newer impact-rated construction across Broward County. The field experience shows up in how we sequence the work:

1. 1
   Measure, template, and diagnose. We inspect the window in its frame, not in a photo. We measure the opening twice, template any curve or angle, and check the rough opening with a level before we quote anything.
2. 2
   Parts decision on paper. We quote OEM PGT parts and quality aftermarket equivalents side by side, with prices next to each line. You see exactly what you are buying and what the trade-off is, in writing.
3. 3
   Warranty registration before the work starts. We verify your existing PGT warranty status, confirm what the manufacturer covers, and register both warranty layers for any new install before the truck leaves your driveway. No fine print surprises later.
4. 4
   Set, shim, seal. We remove the old sash or glass, correct any out-of-square frame condition within reason, set the new unit on shims, and seal with materials rated for South Florida humidity and UV.
5. 5
   Test square, level, and operation. We check plumb on both axes, run the sash through full travel, and watch for any bind or drag. If the pane is not true, the job is not done.
6. 6
   Cleanup and walkthrough. We leave the opening cleaner than we found it, then walk you through what we did and hand you paper copies of every warranty registration and the final invoice.

What PGT Custom & Geometric Windows Costs in Plantation

PGT custom and geometric window work in Plantation runs from roughly $850 for a simple glass replacement in a fixed radius window up to $6,800 for a full custom trapezoid or multi-panel geometric impact unit replacement. Here is the pricing we quote on real jobs:

• PGT WinGuard radius or arched glass replacement (laminated impact): $850-$1,400 per sash
• PGT 400 Series trapezoid or angled window full replacement: $2,200-$4,800 depending on size and impact rating
• PGT slider door roller and track rebuild (Series 5500 and similar): $425-$700
• Mull joint re-seal on multi-panel geometric builds: $300-$600 per joint
• Casement or awning operator replacement with hardware alignment: $225-$425 per window

What moves the price: the size of the unit, whether it is impact-rated, how far out of square the rough opening sits, and whether the existing frame is worth saving. The honest way to know your number is to have us measure. Call (772) 577-2915 for a free estimate – no obligation, no pressure, just a written quote with both warranty layers stated.

Why Plantation Homeowners Call TruePane Windows & Doors for PGT Work

We have served Plantation and Broward County homeowners since 2008 through Dale Kessler’s founding principle: out-of-true installs and voided warranties were problems worth fixing permanently. That is not a slogan. It is how we run every PGT job. Our techs are background-checked and uniformed, and they work in your home the way they would work in their own mother’s. We are authorized installers for more than a dozen manufacturer lines, including PGT, CGI, CWS, ES Windows, and ECO Window Systems, so when a PGT unit is beyond saving, we quote real alternatives side by side and let you compare.

Every job is covered by our Done Right Promise and The Keystone Standard: both warranty layers registered in writing, durations stated, before we leave your driveway. And if something is not done right, we make it right – no paperwork fights, no arguing. We answer our own phones, 24 hours a day, seven days a week. Not a voicemail tree. Not a regional call center. A person who knows Plantation windows.

FAQs