PGT Glass Railing Systems Nationwide | TruePane Windows & Doors

PGT Glass Railing Systems in Plantation: What to Know First

PGT glass railing systems in Plantation typically cost between $180 and $340 per linear foot installed, depending on whether you’re replacing a panel, re-bedding a shoe, or doing a full run around a pool deck. Most single-panel repairs are completed in one visit; a full railing replacement usually takes two to three days. We’re an independent PGT service provider, not a manufacturer affiliate, so our pricing reflects the actual scope of work, not a brand markup. This page is for Plantation homeowners who already own PGT glass railings or are planning to add them, and who want straight answers about what fails, what it costs, and how to avoid paying twice. Call (772) 577-2915 for a free estimate.

Call (772) 577-2915

How PGT Products Fail - and How We Fix Them

PGT builds a solid railing system, but South Florida has a way of finding every weak point in aluminum and glass. Here’s what we see on PGT railings in Plantation, and what we do about it.

• Oxidized shoe moldings on PGT’s 5500 Series railing. The aluminum base shoe sits in constant contact with pool splash-out and sprinkler overspray. Over five to seven years, the factory clear anodizing breaks down and white corrosion creeps under the glass. We strip the shoe, mechanically clean the channel, replace the setting blocks, and re-install with new gaskets. If the shoe is too far gone, we order an OEM replacement rather than patching it.
• Loose glass panels in PGT’s Frameless Series. Frameless panels rely on two or three aluminum spigots fastened to the deck. In Plantation’s wet season, concrete expands and contracts enough that spigot anchors work loose. The glass then rattles in wind and leans out of plumb. We re-set the spigots with proper epoxy anchoring and re-shim the glass so it’s square, level, and in writing before we leave.
• Failed setting blocks causing glass-to-metal contact. PGT uses EPDM setting blocks inside the shoe to keep the glass edge off the aluminum. When those blocks compress or disintegrate, the glass edge rests directly on metal. Any wind load or someone leaning against the panel then creates a stress point. We replace the blocks with OEM or equivalent-durometer EPDM, never off-the-shelf rubber that hardens in two summers.
• Cloudy or hazy glass on PGT’s Coastal Series near saltwater or heavily chlorinated pools. Plantation isn’t beachfront, but homes within a mile of the Intracoastal get enough salt in the air, and pools with high chlorine levels can etch glass over time. If the clouding is surface film, we polish it out. If it’s etched into the glass, we quote a panel replacement and match the existing tint and thickness so you don’t end up with one odd pane.
• Worn top rail gaskets on PGT’s 5500 and 7700 Series. The top rail cap snaps over the glass with a vinyl gasket that hardens and shrinks under UV. Once it shrinks, water gets into the channel and runs down inside the panels. We replace the gasket with a UV-stable profile and re-seat the cap, which is a quick fix if caught early and a bigger job if water has already started corroding the shoe below.

Our PGT Glass Railing Systems Process

Every PGT job follows the same sequence, whether it’s one cracked panel by the spa or a full replacement around the pool cage. There are no shortcuts, and no step gets skipped because we’re running late.

1. 1
   Call and talk to a person. You call (772) 577-2915. A live person answers, day or night. We ask what you’re seeing, where the railing is, and when it started.
2. 2
   Site measurement and condition report. Our technician measures every opening twice and checks the entire run, not just the panel you flagged. We look at the shoe, the anchors, the glass edge condition, and the deck surface.
3. 3
   Parts decision on paper. We show you OEM PGT parts versus quality aftermarket options side by side, with prices. You decide. We don’t decide for you and surprise you later.
4. 4
   The repair or replacement. We remove the affected glass carefully, prep the channel or anchors, and set everything back to our standard: glass plumb, shoe level, gaskets seated, anchors torqued.
5. 5
   Load test and alignment check. We push on every panel, check the gaps, and walk the full run. If it moves, it gets re-done before we call the job finished.
6. 6
   Cleanup and warranty registration. We clean the job site, register both manufacturer warranty layers in writing, and hand you the paperwork before the truck leaves the driveway. If it is not square, level, and in writing, it is not done.

What PGT Glass Railing Systems Costs in Plantation

Here are honest ranges for the PGT railing work we do most often in Plantation. These include labor, materials, and cleanup.

• Single glass panel replacement (PGT Frameless or Coastal Series): $350-$750 per panel, depending on size and glass type.
• Re-bedding a loose or rattling panel: $180-$300 per spigot or shoe section, including new setting blocks and gaskets.
• Full shoe replacement on a 20-foot PGT 5500 Series run: $1,500-$2,800, including new gaskets, blocks, and re-seating all glass.
• Complete new PGT frameless glass railing around a pool deck: $180-$340 per linear foot, depending on glass thickness, gate hardware, and deck condition.
• Top rail gasket replacement (materials and labor): $15-$30 per linear foot.

What moves the price: whether the existing shoe can be saved, how much corrosion got into the channel, whether we need to drill and epoxy new anchors, and whether the glass is a standard size or a custom-cut panel. We quote fixed prices in writing and we don’t add change orders halfway through. Call (772) 577-2915 for a free estimate on your specific railing.

Why Plantation Homeowners Call TruePane Windows & Doors for PGT Work

We’ve been doing this work in Broward County for a long time. Dale Kessler grew up off Broward Boulevard in Plantation, learned glazing at McFatter Technical College in Davie, and spent two decades setting windows and doors on everything from 1960s ranch homes to impact-rated new construction before founding TruePane. When you call us about a PGT railing, you’re talking to a company that knows the product, knows the climate, and answers the phone 24 hours a day. Our technicians are background-checked and uniformed. Every job is covered by the Done Right Promise, and we register both warranty layers in writing before we leave. We also service Andersen, Pella, and CGI railings, so if you have mixed brands on one property, we can handle it in one visit. We stand behind it.

FAQs