Simonton Door Installation Nationwide | TruePane Windows & Doors

Simonton Door Installation: The Plantation Owner’s Guide

We install, replace, and repair Simonton doors throughout Plantation, and we stock the hardware, hinges, rollers, and lock components that fail most often on these units. Most Simonton door installations in Plantation run between $195 and $685 when swapping failed hardware on an existing slab, while full door replacements typically land between $1,200 and $3,400 depending on series, glass package, and whether the frame needs re-setting. The call usually starts the same way: the door suddenly drags against the track, the lock no longer catches clean, or the sliding panel sounds like it’s grinding gravel every time it moves.

Call (772) 577-2915

Simonton builds a solid door, but South Florida humidity and daily use take their toll on moving parts long before the glass or frame gives out. A door that once rolled with two fingers now needs a shoulder. That’s when Plantation homeowners start looking for someone who actually knows Simonton hardware, not someone who will measure once and hope.

Which Simonton Models This Applies To

Simonton’s sliding patio doors, hinged French doors, and StormBreaker Plus impact-rated doors all share common hardware families, but compatibility is not universal across series. The Simonton 5500 and 6500 series sliding doors use a different roller assembly than the StormBreaker Plus line, and the hinge geometry on Simonton French doors changed between older 1990s production and current models. If you can find the AAMA certification label on the door frame edge, it will list the series and manufacturing date. That label is the fastest way to match the right part.

For Plantation homes with original Simonton doors from the 1980s and 1990s, OEM parts are sometimes discontinued. In those cases we source quality aftermarket assemblies milled to the same tolerances, and we tell you on paper which part is OEM versus aftermarket before any work starts. The truth is, aftermarket rollers with sealed stainless bearings often outlast the original nylon-wheel OEM design in Florida’s humidity. We stock roller assemblies, hinge sets, handle sets, multi-point lock components, and weatherstripping for current Simonton production, and we can have discontinued hardware matched within a few days. TruePane is an independent installer and service provider, not affiliated with or authorized by Simonton.

Signs Your Simonton Door Installation Is Failing

• The door drags or binds at the latch point. This is nearly always the roller assembly losing its bearing or the frame settling out of square. In Plantation, seasonal ground shifts from wet summers and dry winters make frame settling common, and the latch side shows it first.
• The lock no longer lines up with the strike plate. When a multi-point lock mechanism starts missing its top or bottom shoot bolts, the door slab has moved or the internal lock rods have worn. Forcing the handle eventually strips the gear inside the lock body.
• You can see daylight or feel air at the bottom corner. The weatherstripping or threshold cap has failed. On Simonton sliders, the interlock at the meeting stile also loses its seal as rollers flatten over years of weight and heat.
• The door sounds like it’s rolling over sand. That’s the sound of disintegrated bearings inside the roller wheels. Once the bearing fragments, the roller body grinds against the track and starts scoring the aluminum.
• Condensation between the glass panes. The insulated glass seal has failed. On Simonton doors this is a sealed-unit replacement, not a hardware fix. We can match the glass package and tint without replacing the entire door.

Replacement Cost & What’s Included

For hardware-only repairs on Simonton doors in Plantation, you’re looking at $195 to $685 installed. That covers the parts, the labor to remove and reset the door slab, and adjusting the final alignment so the door rolls clean and locks without force. Full Simonton-compatible door replacements run $1,200 to $3,400, with the range driven by impact rating, glass package, size, and whether the existing frame is square enough to reuse or needs new construction work.

Every line item is written down before work starts. You see the part cost, the labor cost, and any disposal or threshold work as separate entries. No lump-sum mystery numbers. We register both warranty layers, the manufacturer’s on the parts and ours on the workmanship, in writing before the truck leaves your driveway. Our Done Right Promise covers every Simonton door installation we perform in Plantation. If it is not square, level, and in writing, it is not done.

DIY or Call Us?

There are a few things a Plantation homeowner can safely check before calling. Clean the bottom track with a vacuum and a dry cloth, since packed sand and leaves from daily foot traffic mimic roller failure. Check the visible screws on the handle set and the hinge plates to see if any have backed out. Those are safe, quick checks that cost nothing.

What we don’t recommend is a homeowner pulling a Simonton sliding door out of its frame. These door slabs weigh 80 to 200 pounds, and once the anti-lift clips are removed and the panel tilts out, it can come down hard and fast on hands or tile. The moment you are prying rollers loose or adjusting the frame screws without knowing the plumb and square readings, you’re gambling with a door that will bind worse than before. Call us at (772) 577-2915. We’ll send a uniformed technician who measures the opening twice before touching a screw, because Dale Kessler’s rule has been the same since he learned the trade off Broward Boulevard: if it is not square, level, and in writing, it is not done.

FAQs